Electronic Integrated Systems Mechanic (Title 32) (Permanent)

Duties

As an Electronic Integrated Systems Mechanic (Title 32), WG-8852-12, you will perform the below duties:

Performs operational checks, inspections, tests and troubleshooting on electronic integrated systems composed of a number of sensor subsystems: Integrated Vehicle Health Management System (IVHMS), the Common Missile Warning System (CMWS), the Improved Countermeasure Dispenser System (ICMD), the Night Vision Goggle System (NVG), the Air Data Subsystem, the Attitude Heading Reference System (AHRS) and Doppler/GPS Navigation System (DGNS), Command Instrument Set (CIS) ; a logic subsystem-- the Multiplex Data Bus System (MUX), the Multiplex Remote Terminal Units (MRTU), Data Link Terminal Units (DLTU), and Digital Automatic Flight Control System (DAFCS); and actuating subsystems--, and the Digital Automatic Stabilization System (DASS), which includes the Stability Augmentation System (SAS) and Command Augmentation System (CAS) and Hover Augmentation System (HAS).

Completes operational checks, inspections, tests and troubleshooting of Line Replaceable Units (LRU). Isolates unusual malfunctions using technical manuals, schematics, and wiring diagrams, tools and test equipment including automatic test equipment. Solves problems by analyzing installation, circuitry, and operating characteristics of the systems. Adjusts and aligns sensors, transmitters, amplifiers, power supplies, display devices, controls, actuators, servos, computers and other related components. Removes faulty LRUs for shop repair. Installs serviceable components into aircraft and performs total systems alignments in accordance with existing technical manuals and directives. Accomplishes technical manual compliance and modification of components and systems and completes systems checkout for proper operation. Maintains, modifies, calibrates and inspects a wide variety of user test, measurement, and diagnostic equipment (TMDE).

Completes bench check, testing, repair, inspection, modification, programming, reprogramming, mating, adjusting, alignment, and analyzing of LRUs and shop replaceable units. Uses a variety of test equipment such as automatic test equipment (ATE), oscilloscopes, DTA computer, multi-meters, power-meters, and special purpose bench test sets. Tests and troubleshoots solid state electronic assemblies and subassemblies such as circuit cards, modules, rate gyros, electronic control amplifiers, electro-mechanical assemblies, random access memories, programmable read-only memories and various integrated circuits. Identifies faulty parts and repairs to level authorized. Ensures and certifies operational integrity of various night vision systems, and electro-optical components. Reassembles unit after repair, performs alignment and makes shop checks.

Recommends methods to improve equipment performance, technical data, and maintenance procedures by reporting hardware and software malfunctions, initiates material deficiency reports both on equipment and in technical data, and assists in design changes as necessary. Conducts debriefing of aircrews to determine the nature of system malfunctions, then documents all maintenance performed and records information related to the system, LRU's, or shop repairable units on both aircraft and historical records.

When designated on NGB Flying Status Orders, serves as member of flight crew for the purpose of diagnosing and recording malfunctions, or otherwise determining maintenance and repair requirements.

Guides lower level mechanics in the performance of duties. Conducts on-the-job training on assigned systems and related support equipment and tasks to include classroom instruction as necessary.

Processes and accounts for due-in supply assets. Ensures that material and equipment are properly stored, protected and maintained and that funds are not obligated for material or parts without proper justification.

Prepares for and participates in various types of readiness evaluations such as Operational Readiness Evaluations (ORE), Command Logistics Readiness Inspections (CLRT-X), and Aviation Resource Management Surveys. May be required to perform additional duties such as structural firefighting, aircraft handling, heavy equipment operation, and maintenance of facilities and equipment, or serve as a member of a team to cope with natural disasters or civil emergencies. Complies with safety, fire, security, and housekeeping regulations.

Performs other duties as assigned.

Requirements

Conditions of employment

• NATIONAL GUARD MEMBERSHIP IS REQUIRED. If you are not sure you are eligible for military membership, please contact a National Guard recruiter prior to applying for this position.
• This is an excepted service position that requires membership in a compatible military assignment in the employing state's National Guard, required prior to the effective date of placement.
• Selectee will be required to wear the military uniform.
• Acceptance of an excepted service position constitutes concurrence with these requirements as a condition of employment.
• Applicants who are not currently a member of the National Guard must be eligible for immediate membership and employment in the National Guard in the military grade listed in this announcement.
• Males born after 31 December 1959 must be registered for Selective Service.
• Federal employment suitability as determined by a background investigation.
• May be required to successfully complete a trial period.
• Participation in direct deposit is mandatory.
• This position is not located at a bargaining unit.
• All job seekers will be required to limit their resumes to 2 pages in length when applying for job opportunity announcements (JOAs).

Qualifications

NOTE:Qualifications are based on breadth/level of experience. In addition to describing duties performed, applicants must provide the exact dates of each period of employment (from MM/DD/YY to MM/DD/YY) and the number of hours worked per week if part time. As qualification determinations cannot be made when resumes do not include the required information, failure to provide this information may result in disqualification. Applicants are encouraged to use the USAJOBS Resume Builder to develop their federal resume.

NOTE: All job seekers will be required to limit their resumes to 2 pages in length when applying for job opportunity announcements (JOAs)

WHO CAN APPLY:
GROUP I - All qualified Male/Female Enlisted Member (E4/SPC - E7/SFC) currently employed (permanent) in the Virginia Army National Guard Military Technician Program.
GROUP II - All qualified Virginia Army National Guard Male/Female Enlisted Member (E4/SPC - E7/SFC) , regardless of employment status (Traditional, Military Technician or AGR). To be considered as a Group II applicant, proof of appointment/enlistment in the Virginia National Guard must be attached if the appointment/enlistment occurred within 60 days prior to, or during, the advertisement period.
GROUP III - Individuals eligible for membership in the Virginia Army National Guard.

Military Grades: Enlisted Member (E4/SPC - E7/SFC)

GENERAL EXPERIENCE : Applicant must have experience or training which demonstrates the applicant's knowledge to perform duties such as, install, modify, overhaul, maintain, troubleshoot, repair, align, calibrate, and rebuild multi-system avionics complexes.

SPECIALIZED EXPERIENCE : Applicant must have at least 18 months of specialized experience, equivalent to at least the WG-11 level, or equivalent pay band in other pay systems in the Federal government? This experience may also have been obtained in the private sector but must demonstrate that it is comparable to the WG grade indicated. This experience must include activities such as:

Experience or training demonstrating the ability to repair, align, and adjust major integrated electronic systems such as inertial navigation system, automatic flight control, or fire control system.

Extensive knowledge of electronic, pneumatic, hydraulic, and mechanical systems in order to understand and predict the progressive effects of malfunctions throughout the interrelated units, (e.g., trace an apparent operating error in the hydraulic controls of a gun mount back to the failure of a tactical computer to integrate yaw, pitch, azimuth, and velocity inputs) and to predict areas of technical difficulty in order to assist lower grade employees.

Knowledge of the application of electronic theories and practices to one or more complex integrated systems such as fire control, inertial navigation, or automatic landing control systems.

Knowledge of mathematics including algebra and basic trigonometric functions in order to adapt standard formulas to the specific requirements of the integrated system.

Education

You must provide transcripts or other documentation to support your Educational claims. To receive credit for Education, you must provide documentation of proof that you meet the Education requirements for this position.

Additional information

If you are a male applicant who was born after 12/31/1959 and are required to register under the Military Selective Service Act, the Defense Authorization Act of 1986 requires that you be registered or you are not eligible for appointment in this agency ( ).