Today
Secret
Unspecified
Unspecified
Construction/Facilities
Columbus, OH (On-Site/Office)
Duties
As a ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC, WG-2602-11, you will perform the following duties:
(1) Calibrates and repairs TMDE within support capability and authority including various levels of calibration as designated in technical bulletins, manuals, etc. Performs functional electronic, physical, and radioactive testing involving interpretation and analysis of measurement data, in accordance with cyclic inspection requirements. Aligns, troubleshoots, tests, inspects, repairs, modifies, calibrates and certifies precision measurement equipment such as multimeters, microwave equipment, oscilloscopes, temperature analyzers, mercurial barometers, gage blocks and micrometer caliper dimensional equipment, digital voltmeters, signal generators, torque wrenches, pressure gauges, torque testers, weight scales, electronic counters, radiation monitors, radix calibrators, and radiation dosimeters. Analyzes and isolates component malfunctions; calculates and determines tolerances; and performs tests and calibrations in accordance with instructions, which are often vague and incomplete, and may require the preparation of diagrams and instructions to facilitate the calibration action.
(2) Sets up system test sets and various types of test equipment such as frequency meters, standing wave ratio meters, radio frequency (RF) power meters, function/ arbitrary waveform generator, distortion analyzers, time frequency work stations, oscillators, voltmeters, electronic counters, oscilloscopes, attenuators, decade resistors and capacitors, signal generators, stroboscope, tachometers, pneumatic and hydraulic pressure standards and other physical and electronic tests. Diagnoses equipment, makes repairs, and replaces defective parts/components such as integrated circuits, printed circuit boards, electronic condition coils, radiation detector boards/circuits, crystals, transistors, tubes, transformers, condensers, diodes, relays potentiometers, and related components.
(3) Following repair, tests by applying signals in known amplitude and wave shape into oscilloscopes to observe wave pattern. Isolates faults by taking measurements and comparisons in voltage, amperage, ohms, henries, power factor, watts, temperature, humidity, microns, foot-pounds, decibels, sensitivity, noise, stability, Voltage Standard Wave Ratio (VSWR), impedance, phase, absolute pressure, time intervals, displacement, flow rate, etc., to determine performance of equipment. If signal is distorted, traces it through electronic stages to locate malfunctioning part. Checks sweep rate by feeding known signal to an oscilloscope and observing wave pattern to correct shape and size. Operates equipment to complete range checking for proper operation of positioning controls. Adjusts with trimmer potentiometers; and if calibration is still not possible, adds or removes sufficient resistance to permit balancing of circuit. As needed, contacts the using organization to obtain information concerning the nature of the malfunction. Uses equipment schematics to analyze circuits by preparing block diagram showing major components such as amplifiers, filters, oscillators and indicators.
(4) Determines purpose in operation characteristics of each major section. Refers to technical manuals and manufactures specifications to obtain information on operation characteristics of circuit components such as integrated circuits, microprocessors, decoders, latching networks, notch filters, logics, controllers, programmable gain amplifiers, digital displays, transistors, tubes, transformers, coils, relays, motors, and similar devices. Disassembles, cleans and inspects parts such as printed circuit boards, resistors, capacitors, integrated circuits, relays, chambers, cables, and wiring for evidence or wear or malfunction. Repairs and/or replaces parts as required. Uses special test devices and radioactive samples or other calibrated sources. Tests equipment for sensitivity and correct operation. Observes necessary precautions as stipulated in operational repair manuals. Makes radiation calculations/readings at various distances from the standard ensuring radiation equipment is operating in specified parameters. Performs contamination/radiation surveys on radiation equipment to control/eliminate radiation leakage/contamination.
(5) Performs other duties as assigned.
*The above duty description does not contain all details of the official position description. A copy of the entire position description can be found on FASCLASS by searching the position description (PD#:D1201000). https://acpol2.army.mil/ako/fasclass/search_fs/search_fasclass.asp
Requirements
Conditions of Employment
Ohio Army National Guard Membership is required.
Males born after 31 December 1959 must be registered for Selective Service.
Federal employment suitability as determined by a background investigation.
May be required to successfully complete a probationary period.
Participation in direct deposit is mandatory.
MILITARY REQUIREMENTS:
Compatible military grade and assignment required within one year of the effective date of placement. This is an excepted service position that requires membership in a compatible military assignment in the employing state's National Guard. Applicants who are not currently a member of the Ohio Army National Guard must be eligible for immediate membership. If you are not sure you are eligible for military membership, please contact an Ohio Army National Guard recruiter prior to applying for this position.
Military Grades: E3 through CW3
Other requirements:
1. Must be able to obtain and maintain the appropriate security clearance of the position.
2. This position is covered by the Domestic Violence Misdemeanor Amendment (30 Sep 96) of the Gun Control Act (Lautenberg Amendment) of 1968. An individual convicted of a qualifying crime of domestic violence may not perform the duties of this position.
3. Ability to establish effective professional working relationships with coworkers and customers, contributing to a cooperative working environment and successful accomplishment of the mission.
4. Irregular and/or overtime (compensatory) hours may be required to support operational requirements or contingencies or may be required to work hours outside of the normal duty day.
5. The duties and responsibilities of your job may significantly impact the environment. You are responsible to maintain awareness of your environmental responsibilities as dictated by legal and regulatory requirements, your organization, and its changing mission.
Qualifications
GENERAL EXPERIENCE : Experience or training which demonstrates a working knowledge of electronic principles involved in the generation and measurement of such elements as voltage, current, impedance, capacitance, frequency, and inductance. Experience in the use of various precision measurement instruments and standards.
SPECIALIZED EXPERIENCE : Experience or training with basic application of operating principles such as the production and utilization of oscillations over a broad range of frequencies; signal and waveform behavior, distortion, and amplification; pulse, trigger, and synchronization techniques; digital/analog processing and data conversion techniques; and a variety of display and indication methods. Experience in tracing signals and voltage paths, and skilled in the analysis of waveform characteristics such as timing, duration, frequency, and phasing. Originates test set-ups to isolate malfunctions and check performance characteristics of special or unique test panels or mockups. Experience in interpreting and applying a variety of technical electronic information such as schematic symbols, mathematical expressions and formulas, calibration procedures, and other reference materials. Experience in applying established techniques and methods of repair, testing, alignment, and calibration of equipment, which serves as test equipment or precision measurement standards. Experience in utilizing electronic circuits to measure electronic or electrical quantities to determine the performance characteristics and accuracy of other instruments and equipment.
Education
This job does not have an education qualification requirement.
Additional information
***If serving under an incentive contract, termination of that incentive(s) will occur effective one day prior to your AGR, Permanent Military Technician, or Indefinite Military Technician start date. Temporary Military Technicians will have their incentive terminated if their tour exceeds 179 days in a continuous 12-month period.***
If you are a male applicant who was born after 12/31/1959 and are required to register under the Military Selective Service Act, the Defense Authorization Act of 1986 requires that you be registered or you are not eligible for appointment in this agency ( https://www.sss.gov/RegVer/wfRegistration.aspx ).
You will be evaluated for this job based on how well you meet the qualifications above.
Once the announcement has closed, your resume and supporting documentation will be used to determine if you meet the qualifications listed on this announcement. If you are minimally qualified, your resume and supporting documentation will be compared to your responses on the assessment questionnaire to determine your level of experience. If you rate yourself higher than is supported by your application package, your responses may be adjusted and/or you may be excluded from consideration for this position. If you are found to be among the top qualified candidates, you will be referred to the selecting official for employment consideration.
Your qualifications will be evaluated on the following competencies (knowledge, skills, abilities and other characteristics):
To apply for this position, you must submit a complete Application Package which includes:
Resume showing current Military grade, current MOS, current unit of assignment, work schedule, hours worked per week, dates (including Month and Year, e.g., 02/2017, Feb 2017, etc.) of employment, and all duties performed.
How to Apply
To apply for this position, you must complete the online application/Occupational Questionnaire and submit the documentation specified in the Required Documents section below.
A complete application package must be submitted by 11:59 PM (EST) on the closing date of the announcement to receive consideration.
To begin, click Apply to access the online application. You will need to be logged into your USAJOBS account to apply. If you do not have a USAJOBS account, you will need to create one before beginning the application.
Follow the prompts to select your resume and/or other supporting documents to be included with your application package. You will have the opportunity to upload additional documents to include in your application before it is submitted. Your uploaded documents may take several hours to clear the virus scan process.
After acknowledging you have reviewed your application package, complete the Include Personal Information section as you deem appropriate and click to continue with the application process.
You will be taken to the online application which you must complete in order to apply for the position. Complete the online application, verify the required documentation is included with your application package, and submit the application.
To verify the status of your application, log into your USAJOBS account ( https://my.usajobs.gov/Account/Login ), all of your applications will appear on the Welcome screen. The Application Status will appear along with the date your application was last updated. For information on what each Application Status means, visit: https://www.usajobs.gov/Help/how-to/application/status/ .
Agency contact information
Adam Jenkins
Phone (614) 356-7967 Email adam.d.jenkins11.civ@army.mil
Address OH G4 SMO CSMS
3990 East Broad St
Columbus, OH 43213
US
Next steps
Once your online application is submitted you will receive a confirmation notification by email. Your application will be evaluated by the Human Resources Office to determine your eligibility for the position. After the evaluation is complete, you will receive another notification regarding the status of your application.
Fair & Transparent
The Federal hiring process is set up to be fair and transparent. Please read the following guidance.
As a ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC, WG-2602-11, you will perform the following duties:
(1) Calibrates and repairs TMDE within support capability and authority including various levels of calibration as designated in technical bulletins, manuals, etc. Performs functional electronic, physical, and radioactive testing involving interpretation and analysis of measurement data, in accordance with cyclic inspection requirements. Aligns, troubleshoots, tests, inspects, repairs, modifies, calibrates and certifies precision measurement equipment such as multimeters, microwave equipment, oscilloscopes, temperature analyzers, mercurial barometers, gage blocks and micrometer caliper dimensional equipment, digital voltmeters, signal generators, torque wrenches, pressure gauges, torque testers, weight scales, electronic counters, radiation monitors, radix calibrators, and radiation dosimeters. Analyzes and isolates component malfunctions; calculates and determines tolerances; and performs tests and calibrations in accordance with instructions, which are often vague and incomplete, and may require the preparation of diagrams and instructions to facilitate the calibration action.
(2) Sets up system test sets and various types of test equipment such as frequency meters, standing wave ratio meters, radio frequency (RF) power meters, function/ arbitrary waveform generator, distortion analyzers, time frequency work stations, oscillators, voltmeters, electronic counters, oscilloscopes, attenuators, decade resistors and capacitors, signal generators, stroboscope, tachometers, pneumatic and hydraulic pressure standards and other physical and electronic tests. Diagnoses equipment, makes repairs, and replaces defective parts/components such as integrated circuits, printed circuit boards, electronic condition coils, radiation detector boards/circuits, crystals, transistors, tubes, transformers, condensers, diodes, relays potentiometers, and related components.
(3) Following repair, tests by applying signals in known amplitude and wave shape into oscilloscopes to observe wave pattern. Isolates faults by taking measurements and comparisons in voltage, amperage, ohms, henries, power factor, watts, temperature, humidity, microns, foot-pounds, decibels, sensitivity, noise, stability, Voltage Standard Wave Ratio (VSWR), impedance, phase, absolute pressure, time intervals, displacement, flow rate, etc., to determine performance of equipment. If signal is distorted, traces it through electronic stages to locate malfunctioning part. Checks sweep rate by feeding known signal to an oscilloscope and observing wave pattern to correct shape and size. Operates equipment to complete range checking for proper operation of positioning controls. Adjusts with trimmer potentiometers; and if calibration is still not possible, adds or removes sufficient resistance to permit balancing of circuit. As needed, contacts the using organization to obtain information concerning the nature of the malfunction. Uses equipment schematics to analyze circuits by preparing block diagram showing major components such as amplifiers, filters, oscillators and indicators.
(4) Determines purpose in operation characteristics of each major section. Refers to technical manuals and manufactures specifications to obtain information on operation characteristics of circuit components such as integrated circuits, microprocessors, decoders, latching networks, notch filters, logics, controllers, programmable gain amplifiers, digital displays, transistors, tubes, transformers, coils, relays, motors, and similar devices. Disassembles, cleans and inspects parts such as printed circuit boards, resistors, capacitors, integrated circuits, relays, chambers, cables, and wiring for evidence or wear or malfunction. Repairs and/or replaces parts as required. Uses special test devices and radioactive samples or other calibrated sources. Tests equipment for sensitivity and correct operation. Observes necessary precautions as stipulated in operational repair manuals. Makes radiation calculations/readings at various distances from the standard ensuring radiation equipment is operating in specified parameters. Performs contamination/radiation surveys on radiation equipment to control/eliminate radiation leakage/contamination.
(5) Performs other duties as assigned.
*The above duty description does not contain all details of the official position description. A copy of the entire position description can be found on FASCLASS by searching the position description (PD#:D1201000). https://acpol2.army.mil/ako/fasclass/search_fs/search_fasclass.asp
Requirements
Conditions of Employment
Ohio Army National Guard Membership is required.
Males born after 31 December 1959 must be registered for Selective Service.
Federal employment suitability as determined by a background investigation.
May be required to successfully complete a probationary period.
Participation in direct deposit is mandatory.
MILITARY REQUIREMENTS:
Compatible military grade and assignment required within one year of the effective date of placement. This is an excepted service position that requires membership in a compatible military assignment in the employing state's National Guard. Applicants who are not currently a member of the Ohio Army National Guard must be eligible for immediate membership. If you are not sure you are eligible for military membership, please contact an Ohio Army National Guard recruiter prior to applying for this position.
Military Grades: E3 through CW3
Other requirements:
1. Must be able to obtain and maintain the appropriate security clearance of the position.
2. This position is covered by the Domestic Violence Misdemeanor Amendment (30 Sep 96) of the Gun Control Act (Lautenberg Amendment) of 1968. An individual convicted of a qualifying crime of domestic violence may not perform the duties of this position.
3. Ability to establish effective professional working relationships with coworkers and customers, contributing to a cooperative working environment and successful accomplishment of the mission.
4. Irregular and/or overtime (compensatory) hours may be required to support operational requirements or contingencies or may be required to work hours outside of the normal duty day.
5. The duties and responsibilities of your job may significantly impact the environment. You are responsible to maintain awareness of your environmental responsibilities as dictated by legal and regulatory requirements, your organization, and its changing mission.
Qualifications
GENERAL EXPERIENCE : Experience or training which demonstrates a working knowledge of electronic principles involved in the generation and measurement of such elements as voltage, current, impedance, capacitance, frequency, and inductance. Experience in the use of various precision measurement instruments and standards.
SPECIALIZED EXPERIENCE : Experience or training with basic application of operating principles such as the production and utilization of oscillations over a broad range of frequencies; signal and waveform behavior, distortion, and amplification; pulse, trigger, and synchronization techniques; digital/analog processing and data conversion techniques; and a variety of display and indication methods. Experience in tracing signals and voltage paths, and skilled in the analysis of waveform characteristics such as timing, duration, frequency, and phasing. Originates test set-ups to isolate malfunctions and check performance characteristics of special or unique test panels or mockups. Experience in interpreting and applying a variety of technical electronic information such as schematic symbols, mathematical expressions and formulas, calibration procedures, and other reference materials. Experience in applying established techniques and methods of repair, testing, alignment, and calibration of equipment, which serves as test equipment or precision measurement standards. Experience in utilizing electronic circuits to measure electronic or electrical quantities to determine the performance characteristics and accuracy of other instruments and equipment.
Education
This job does not have an education qualification requirement.
Additional information
***If serving under an incentive contract, termination of that incentive(s) will occur effective one day prior to your AGR, Permanent Military Technician, or Indefinite Military Technician start date. Temporary Military Technicians will have their incentive terminated if their tour exceeds 179 days in a continuous 12-month period.***
If you are a male applicant who was born after 12/31/1959 and are required to register under the Military Selective Service Act, the Defense Authorization Act of 1986 requires that you be registered or you are not eligible for appointment in this agency ( https://www.sss.gov/RegVer/wfRegistration.aspx ).
- Benefits
Help
A career with the U.S. government provides employees with a comprehensive benefits package. As a federal employee, you and your family will have access to a range of benefits that are designed to make your federal career very rewarding. Opens in a new window Learn more about federal benefits .
Review our benefits
Eligibility for benefits depends on the type of position you hold and whether your position is full-time, part-time or intermittent. Contact the hiring agency for more information on the specific benefits offered.
You will be evaluated for this job based on how well you meet the qualifications above.
Once the announcement has closed, your resume and supporting documentation will be used to determine if you meet the qualifications listed on this announcement. If you are minimally qualified, your resume and supporting documentation will be compared to your responses on the assessment questionnaire to determine your level of experience. If you rate yourself higher than is supported by your application package, your responses may be adjusted and/or you may be excluded from consideration for this position. If you are found to be among the top qualified candidates, you will be referred to the selecting official for employment consideration.
Your qualifications will be evaluated on the following competencies (knowledge, skills, abilities and other characteristics):
- Troubleshooting (Electronic Equipment)
- Use of Test Equipment: Electronics
- Benefits
Help
A career with the U.S. government provides employees with a comprehensive benefits package. As a federal employee, you and your family will have access to a range of benefits that are designed to make your federal career very rewarding. Opens in a new window Learn more about federal benefits .
Review our benefits
Eligibility for benefits depends on the type of position you hold and whether your position is full-time, part-time or intermittent. Contact the hiring agency for more information on the specific benefits offered. - Required Documents
As a new or existing federal employee, you and your family may have access to a range of benefits. Your benefits depend on the type of position you have - whether you're a permanent, part-time, temporary or an intermittent employee. You may be eligible for the following benefits, however, check with your agency to make sure you're eligible under their policies.
To apply for this position, you must submit a complete Application Package which includes:
Resume showing current Military grade, current MOS, current unit of assignment, work schedule, hours worked per week, dates (including Month and Year, e.g., 02/2017, Feb 2017, etc.) of employment, and all duties performed. - How to Apply
To apply for this position, you must complete the online application/Occupational Questionnaire and submit the documentation specified in the Required Documents section below.
A complete application package must be submitted by 11:59 PM (EST) on the closing date of the announcement to receive consideration.
To begin, click Apply to access the online application. You will need to be logged into your USAJOBS account to apply. If you do not have a USAJOBS account, you will need to create one before beginning the application.
Follow the prompts to select your resume and/or other supporting documents to be included with your application package. You will have the opportunity to upload additional documents to include in your application before it is submitted. Your uploaded documents may take several hours to clear the virus scan process.
After acknowledging you have reviewed your application package, complete the Include Personal Information section as you deem appropriate and click to continue with the application process.
You will be taken to the online application which you must complete in order to apply for the position. Complete the online application, verify the required documentation is included with your application package, and submit the application.
To verify the status of your application, log into your USAJOBS account ( https://my.usajobs.gov/Account/Login ), all of your applications will appear on the Welcome screen. The Application Status will appear along with the date your application was last updated. For information on what each Application Status means, visit: https://www.usajobs.gov/Help/how-to/application/status/ .
Agency contact information
Adam Jenkins
Phone (614) 356-7967 Email adam.d.jenkins11.civ@army.mil
Address OH G4 SMO CSMS
3990 East Broad St
Columbus, OH 43213
US
Next steps
Once your online application is submitted you will receive a confirmation notification by email. Your application will be evaluated by the Human Resources Office to determine your eligibility for the position. After the evaluation is complete, you will receive another notification regarding the status of your application. - Fair and Transparent
The Federal hiring process is set up to be fair and transparent. Please read the following guidance.
- Criminal history inquiries
- Equal Employment Opportunity (EEO) Policy
- Financial suitability
- New employee probationary period
- Privacy Act
- Reasonable accommodation policy
- Selective Service
- Signature and false statements
- Social security number request
To apply for this position, you must submit a complete Application Package which includes:
Resume showing current Military grade, current MOS, current unit of assignment, work schedule, hours worked per week, dates (including Month and Year, e.g., 02/2017, Feb 2017, etc.) of employment, and all duties performed.
How to Apply
To apply for this position, you must complete the online application/Occupational Questionnaire and submit the documentation specified in the Required Documents section below.
A complete application package must be submitted by 11:59 PM (EST) on the closing date of the announcement to receive consideration.
To begin, click Apply to access the online application. You will need to be logged into your USAJOBS account to apply. If you do not have a USAJOBS account, you will need to create one before beginning the application.
Follow the prompts to select your resume and/or other supporting documents to be included with your application package. You will have the opportunity to upload additional documents to include in your application before it is submitted. Your uploaded documents may take several hours to clear the virus scan process.
After acknowledging you have reviewed your application package, complete the Include Personal Information section as you deem appropriate and click to continue with the application process.
You will be taken to the online application which you must complete in order to apply for the position. Complete the online application, verify the required documentation is included with your application package, and submit the application.
To verify the status of your application, log into your USAJOBS account ( https://my.usajobs.gov/Account/Login ), all of your applications will appear on the Welcome screen. The Application Status will appear along with the date your application was last updated. For information on what each Application Status means, visit: https://www.usajobs.gov/Help/how-to/application/status/ .
Agency contact information
Adam Jenkins
Phone (614) 356-7967 Email adam.d.jenkins11.civ@army.mil
Address OH G4 SMO CSMS
3990 East Broad St
Columbus, OH 43213
US
Next steps
Once your online application is submitted you will receive a confirmation notification by email. Your application will be evaluated by the Human Resources Office to determine your eligibility for the position. After the evaluation is complete, you will receive another notification regarding the status of your application.
Fair & Transparent
The Federal hiring process is set up to be fair and transparent. Please read the following guidance.
- Criminal history inquiries
- Equal Employment Opportunity (EEO) Policy
- Financial suitability
- New employee probationary period
- Privacy Act
- Reasonable accommodation policy
- Selective Service
- Signature and false statements
- Social security number request
group id: DOA
